DEBAG error codes
D’Heldt distributes high-quality bread ovens from DEBAG, a German company known for combining tradition and innovation. A key advantage of these appliances is their comprehensive diagnostics. Through internal sensors, the ovens themselves detect where there may be a problem. Thus, these industrial bakery machines indicate with warning messages and error codes when everything is not going as it should. Use this overview to decipher the various messages and solve problems efficiently.
Identify DEBAG error code
Is there a problem with your Dila bread oven from DEBAG? Then you will hear a short beep and a code appears on the display where the baking time usually counts down. The unit here shows either a “Hint message” or warning message or an “Error message” or error code. Below are all the messages, the problem they detect and (a) possible solution(s). Do the solutions not provide a solution for your baking oven, or does the message keep appearing? Contact us immediately and one of our experienced technicians will review the problem on-site as soon as possible.
DEBAG alert messages
The H codes indicate minor faults or forgetfulness, which you can easily fix yourself. Caution: some notifications may still allow the oven to continue working. In the long run, they do cause damage to your appliance. Therefore, solve them as soon as possible.
| Code | Problem | Solution |
| H02 | The oven is not yet ready to bake. | Unload the oven and wait until the START button indicates it is ready. |
| H03 | The oven door is still open | .Close the oven door so that baking can begin. |
| H04 | The emergency release is used to open the oven. | Open the door by pressing the DOOR button. |
| H05 | The level in the water tank is too low, while water is crucial for the proper operation of a steam oven. | Replenish the water supply. |
| H06 | The oven door was opened and closed again without ending the baking program. | Open the door by pressing the DOOR button, which will automatically stop the baking program. |
| H07 | The door doesn’t open as it should. | Push the door firmly and open it again. If necessary, use the emergency opening via the cord. Contact D’Heldt if the problem persists. |
| H08 | The temperature is too high to start the baking process | Wait until the oven indicates that it is ready to start baking. |
| H09 | The furnace is in need of maintenance. | Contact D’Heldt and schedule a maintenance service. |
DEBAG error codes
Er codes indicate larger problems that require targeted action to fix. Is your DEBAG bread oven no longer working and yet not giving an error code? First check the power supply and otherwise contact D’Heldt for a quick repair.
| Code | Problem | Solution |
| Er00 | Fault code Er02 is repeated. | Try the solutions for fault code Er02 or turn off the oven. |
| Er02 | The temperature in the oven is too high or a fuse is broken. | Wait 5 minutes for the code to disappear automatically. Reset the oven using the red button on the back of the unit. Check your fuse box. |
| Er03 | The temperature sensor in the baking chamber is broken. | Contact D’Heldt to replace the sensor. |
| Er04 | Een brede foutcode waar heel wat mogelijke defecten onder vallen. | Contacteer D’Heldt. |
| Er05 | The temperature sensor in the control electronics is broken. | Contact D’Heldt to replace the sensor. |
| Er06 | The oven temperature is too high. | Clean the vents. Provide clearance around the oven. |
| Er09 | The oven temperature is too low. | Turn the oven off and on again. |
| Er13 | The heater of the external evaporator (if any) is not working. | Reset the oven using the red button on the back of the unit. Turn the oven off and on again. |
| Er20 | The temperature sensor in the driving chamber is broken. | Contact D’Heldt to replace the sensor. |
| Er21 | The humidity sensor in the row chamber is broken | Contact D’Heldt to replace the sensor. |
| Er35 | The battery for storing program settings is low. | Contact D’Heldt to replace the battery. |
| Er39 | The limescale filter needs replacement. | Replace the limescale filter at the back of the furnace, near the connection to the water supply. |
| Er41 | There is a communication error between the dual ovens (if any). | Check the cable between both furnaces. Check the voltage of both furnaces. |
DEBAG failure prevention
Warning messages and error messages are there to help you, not to point out omissions or errors. Nevertheless, it is possible to avoid many malfunctions and defects by maintaining your bakery machines according to the rules of the art. Furthermore, it is a good idea to call on D’Heldt’s professional service at least annually. During preventive maintenance, we provide at least a thorough cleaning and descaling of your machine. Furthermore, if necessary, we replace parts that threaten to cause you problems.
D’Heldt, your DEBAG expert
D’Heldt has more than 60 years of experience in industrial food machinery. Therefore, there is no failure, warning message or error code that holds secrets from our professional technicians. Problems or malfunctions with your DEBAG bread oven? Contact us, we will provide the solution.